Veritas™ 5250 Appliance Hardware Installation Guide

Last Published:
Product(s): Appliances (Version Not Specified)
Platform: Veritas 5250
  1. Hardware overview
    1.  
      About the appliance and the storage shelves
    2.  
      Appliance disk drives
    3. About the 5250 Appliance control panel
      1.  
        About the System Status LED states
      2.  
        About the Power button LED states
    4.  
      Appliance rear panel
    5.  
      Storage shelf disk drives
    6.  
      Storage shelf control panel
    7.  
      Storage shelf rear panel
    8.  
      Cables
    9.  
      About IPMI configuration
    10.  
      Product documentation
  2. Preinstallation requirements
    1.  
      Customer-provided environment and supplies
    2.  
      Appliance shipping container contents
    3.  
      Storage shelf shipping container contents
    4.  
      Best practices for rack installation
    5.  
      Determining rack locations
    6.  
      Storage shelf rack requirements
    7.  
      Heat dissipation
    8.  
      Verifying SAS-3 cable length
    9.  
      Prerequisites for IPMI configuration
  3. S Series Appliance installation procedures
    1.  
      Installing the storage shelf rack rails
    2.  
      Installing the storage shelf into a rack
    3.  
      Attaching the storage shelf bezel
    4.  
      Installing the appliance rack rails
    5.  
      Installing the appliance into a rack
    6.  
      Understanding appliance and S Series Storage Shelf connections
    7.  
      Connecting an appliance to one storage shelf
    8.  
      Connecting an appliance to more than one storage shelf
  4. D Series Appliance installation procedures
    1.  
      Installing the storage shelf rack rails
    2.  
      Installing the storage shelf into a rack
    3.  
      Installing the appliance rack rails
    4.  
      Installing the appliance into a rack
    5.  
      Understanding appliance and D Series Storage Shelf connections
    6.  
      Connecting an appliance to one storage shelf
    7.  
      Connecting an appliance to more than one storage shelf
  5. Next steps after installation
    1.  
      Connecting the network cables
    2.  
      Connecting the power cords
    3.  
      Turning on the hardware and verifying operation
    4.  
      Configuring the IPMI port from the NetBackup Appliance Shell Menu
    5.  
      Configuring the Veritas Remote Management Interface from a Flex Appliance
    6.  
      Configuring the Veritas Remote Management Interface using laptop
    7.  
      Accessing and using the Veritas Remote Management interface
  6. Appendix A. Adding one or more storage shelves to an operating appliance that does not have any storage shelves
    1.  
      Overview
    2.  
      Preparing the appliance
    3.  
      Removing the appliance cover
    4.  
      Installing the Expansion Storage Kit components
    5.  
      Replacing the appliance cover
    6. Connecting the S Series storage shelves to the appliance
      1.  
        Connecting one S Series storage shelf to an appliance
      2.  
        Connecting two S Series storage shelves to an appliance
      3.  
        Connecting three S Series storage shelves to an appliance
      4.  
        Connecting four S Series storage shelves to an appliance
      5.  
        Connecting the fifth S Series storage shelf to an appliance
      6.  
        Connecting the sixth S Series storage shelf to an appliance
    7. Connecting the D Series storage shelves to the appliance
      1.  
        Connecting one D Series storage shelf to an appliance
      2.  
        Connecting two D Series storage shelves to an appliance
      3.  
        Connecting three D Series storage shelves to an appliance
      4.  
        Connecting four D Series storage shelves to an appliance
      5.  
        Connecting the fifth D Series storage shelf to an appliance
      6.  
        Connecting the sixth D Series storage shelf to an appliance
  7. Appendix B. Adding storage shelves to an operating appliance that has at least one storage shelf attached
    1.  
      Overview
    2.  
      Moving the MSDP partition from a base disk to an expansion disk for optimum performance
    3.  
      Additional storage shelf scenarios
    4.  
      Installing S Series storage shelves to an appliance that has at least one storage shelf
    5. Recabling to connect additional S Series storage shelves
      1.  
        Connecting additional shelves to an appliance that already has one operating shelf
      2.  
        Connecting additional shelves to an appliance that already has two operating shelves
      3.  
        Connecting a storage shelf to an appliance that already has three operating shelves
    6.  
      Installing D Series storage shelves to an appliance that has at least one storage shelf
    7. Recabling to connect additional D Series storage shelves
      1.  
        Connecting additional shelves to an appliance that already has one operating shelf
      2.  
        Connecting additional shelves to an appliance that already has two operating shelf
      3.  
        Connecting additional shelves to an appliance that already has three operating shelf
  8. Appendix C. Configuring the disk space for new NetBackup Expansion Storage Shelves
    1.  
      Adding the disk space of additional storage shelves from the NetBackup Appliance Shell Menu
    2.  
      Adding the disk space of additional storage shelves from the NetBackup Appliance Web Console
  9. Appendix D. Configuring the disk space for new Flex Expansion Storage Shelves
    1.  
      Adding the disk space of an Expansion Storage Shelf from the Flex Appliance Console
  10.  
    Index

Configuring the Veritas Remote Management Interface from a Flex Appliance

Veritas Flex Appliance release does not support configuring the IPMI port through the Flex Appliance Shell.

To configure the dedicated Veritas Remote Management Interface (IPMI) LAN settings in the BIOS

  1. Connect a standard video cable between the VGA (Video Graphics Array) port and the computer monitor
  2. Connect a keyboard to a USB port at the rear of the Flex 5250 appliance.
  3. Ensure that the power cords are connected to a power supply and press the power switch on the front panel.
  4. The prompt about accessing the BIOS at the beginning of the startup cycle appears. Wait until the Veritas logo shows up and press F2 to enter the initial BIOS setup screen. The initial setup dialog box appears and prompts you.

    Warning:

    When you are in the BIOS, do not perform any other steps other than the ones mentioned in this section.

    Note:

    If you miss the initial setup dialog box prompt in step 4, the appliance shell appears. Shut down and restart the appliance and try accessing the BIOS menu again.

    The Setup Menu page appears and the Main menu option should be highlighted.

  5. Use the down key on the keyboard and navigate to the Server Management menu option. Press Enter.
  6. Press the up or down key on the keyboard to navigate to BMC LAN Configuration. Press Enter.
  7. The BMC LAN Configuration options screen appears.
  8. Navigate to the Dedicated Management LAN Configuration option. Use the information supplied by the customer to fill in the following fields: IP Source, IP address, Subnet mask, Gateway IP.
  9. To save your BIOS changes, press F10.
  10. Press Y to save and exit. The appliance restarts itself.