Veritas NetBackup™ Appliance Commands Reference Guide
- Overview
- Appendix A. Main > Appliance commands
- Appendix B. Main > Manage > FibreChannel commands
- Appendix C. Main > Manage > Libraries commands
- Appendix D. Main > Manage > Libraries > Advanced > ACS commands
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- Appendix E. Main > Manage > License commands
- Appendix F. Main > Manage > MountPoints commands
- Appendix G. Main > Manage > NetBackup CLI commands
- Appendix H. Main > Manage > OpenStorage commands
- Appendix I. Main > Manage > Software commands
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > LiveUpdateClients
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- Manage > Software > VxUpdate
- Appendix J. Main > Manage > Storage commands
- Appendix K. Main > Manage > Tapes commands
- Appendix L. Main > Manage > Certificates commands
- Appendix M. Main > Monitor commands
- Appendix N. Main > Network commands
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- Appendix O. Main > Network > Security (IPsec) commands
- Appendix P. Main > Reports commands
- Appendix Q. Main > Settings commands
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > LiveUpdateServer
- Settings > NetBackup
- Settings > Password
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- Appendix R. Main > Settings > Alerts commands
- Appendix S. Main > Settings > Notifications view commands
- Appendix T. Main > Settings > Security commands
- Appendix U. Main > Support commands
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
Name
Main > Manage > Storage > Remove — Use this command to remove a storage disk.
SYNOPSIS
Remove DiskID
DESCRIPTION
The command removes a storage disk and changes the state to New Available. You can remove disks with status In Use that do not contain any partitions. You can also remove disks with status Foreign.
If the disk has a In Use status and has partitions, you must first move the partitions to other disks. Use the Show Distribution command to see the partitions that are on the disk and then use the Move command to move the partitions to another disk. Once the partitions have been moved, try removing the disk again.
A disk with status Foreign may have data. If you try to remove such a disk, any data present on it is also removed.
OPTIONS
- Remove DiskID
Use to remove an existing disk and changes the state to New Available. Retrieve the disk ID by running the Show Disk command. For example, a sample Disk ID is S0001FB3BC00000A62501ABDA0000009se.
Warning:
After removing a storage disk, if the appliance reboots it can hang and display the Boot splash screen. Press the ESC key to proceed. The RAID controller firmware provides step-by-step instructions to help you boot the appliance.
EXAMPLES
The following is an example of the information that is displayed when you run the Remove Disk ID command.
Storage > Remove S000162501ABDA000009se
- [Info] Performing sanity check on disks and partitions...(5 mins approx)
- [Info] Checking the type of 'S000162501ABDA000009se' disk...
- [Info] Checking the state of 'S000162501ABDA000009se' disk...
- [Info] Removing the 'S000162501ABDA000009se' disk space
from 'Unallocated'...
- [Info] Succeeded.
The following output displays the updated status of the removed storage expansion unit after using the Show Disk command.
Storage> Show Disk ------------------------------------------------------------------------- Disk ID | Type |Total |Unallocated| Status ------------------------------------------------------------------------- SE000000000000000000se|System |150 GB| - |In Use S0001FB3BC00A0000009se|Base |150 GB| 33.968 GB |In Use S000162501ABDA000009se|Expansion | 35 TB| - |New Available You cannot issue commands for disks with the status 'n/a'.