Veritas NetBackup™ Appliance Commands Reference Guide
- Overview
- Appendix A. Main > Appliance commands
- Appendix B. Main > Manage > FibreChannel commands
- Appendix C. Main > Manage > Libraries commands
- Appendix D. Main > Manage > Libraries > Advanced > ACS commands
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- Appendix E. Main > Manage > License commands
- Appendix F. Main > Manage > MountPoints commands
- Appendix G. Main > Manage > NetBackup CLI commands
- Appendix H. Main > Manage > OpenStorage commands
- Appendix I. Main > Manage > Software commands
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > LiveUpdateClients
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- Manage > Software > VxUpdate
- Appendix J. Main > Manage > Storage commands
- Appendix K. Main > Manage > Tapes commands
- Appendix L. Main > Manage > Certificates commands
- Appendix M. Main > Monitor commands
- Appendix N. Main > Network commands
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- Appendix O. Main > Network > Security (IPsec) commands
- Appendix P. Main > Reports commands
- Appendix Q. Main > Settings commands
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > LiveUpdateServer
- Settings > NetBackup
- Settings > Password
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- Appendix R. Main > Settings > Alerts commands
- Appendix S. Main > Settings > Notifications view commands
- Appendix T. Main > Settings > Security commands
- Appendix U. Main > Support commands
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
Name
Main > Settings > LogForwarding — Enable/disable, and manage settings to forward logs to an external log management server.
SYNOPSIS
LogForwarding Enable
LogForwarding Disable
LogForwarding Interval
LogForwarding Share
LogForwarding Show
DESCRIPTION
Use this command to forward appliance logs to an external management server. Currently, only syslog forwarding is supported.
OPTIONS
- LogForwarding Enable
Enable syslog forwarding functionality on the appliance. The command requires you to specify the following:
Target server name or IP address
Server port
Protocol (UDP/TCP)
Forwarding interval in minutes (0/15/30/45/60)
Enabling TLS (yes/no)
- LogForwarding Interval
Set or change how often syslogs are forwarded as follows:
- Forward syslogs as they are generated.
- Forward the syslogs every 15 minutes.
- Forward the syslogs every 30 minutes.
- Forward the syslogs every 45 minutes.
- Forward the syslogs every 60 minutes.
- LogForwarding Share Open
Open NFS and CIFS shares to on the appliance. Make sure that you have uploaded valid certificates to an opened share before you enable the TLS on the appliance. Two certificates and one private key are required as follows:
ca-server.pem
nba-rsyslog.pem
nba-rsyslog.key
- LogForwarding Share Close
Close the NFS and CIFS shares to on the appliance for security purpose.
- LogForwarding Show
View the status of the current log forwarding configuration.
- LogForwarding Disable
Disable the Log Forwarding feature and delete the current log forwarding configuration.
EXAMPLES
- Enable syslog forwarding on the appliance using TLS.
abc123.LogForwarding> enable
- [Info] Only syslog forwarding is supported at this time.
>> Enter server name or IP address: Veritas
>> Enter server port: 514
>> Select Protocol [UDP, TCP](TCP)
>> Set interval in minutes: [0, 15, 30, 45, 60](15)
>> Enable TLS(Only Anonymous authentication mode is supported)?
[yes, no](yes) Yes
- [Info] Summary:
Target server name or IP address: Veritas
Port: 514
Protocol: TCP
Interval: 15 minutes
TLS: no
Do you want to continue? [yes, no] (yes) y
- [Info] Applying the changes...
- [Info] Logs are scheduled for forwarding every 15 minutes.
- [Info] Syslog forwarding is enabled.