Veritas Access 3360 Appliance Hardware Installation Guide

Last Published:
Product(s): Appliances (8.4, 8.3, 8.2)
Platform: Veritas 3360
  1. Overview
    1.  
      About the Veritas Access 3360 Appliance
    2.  
      Supported software
    3.  
      Access 3360 compute node and 5U84 storage shelves
    4.  
      Access 3360 compute node disk drives
    5. About the compute node control panel
      1.  
        About the System Status LED states
      2.  
        About the Power button LED states
    6.  
      Access 3360 compute node rear panel
    7.  
      5U84 storage shelf drawers and disk drives
    8.  
      5U84 storage shelf control panel
    9.  
      5U84 storage shelf rear panel
    10.  
      5U84 storage shelf RAID controller
    11.  
      5U84 storage shelf Expansion module
    12.  
      Cables and connectors
    13.  
      About IPMI configuration
  2. Pre-installation requirements
    1.  
      Customer-provided environment and supplies
    2.  
      Storage shelf shipping container contents
    3.  
      Compute node shipping container contents
    4.  
      Dimensions and determining rack locations
    5.  
      Best practices for rack installation
    6.  
      Heat dissipation guidelines
    7.  
      Cable length verification
    8.  
      Prerequisites for IPMI configuration
  3. Hardware installation procedures
    1.  
      Overview
    2.  
      Installing a storage shelf
    3.  
      Installing disk drives into a storage shelf
    4.  
      Installing the storage shelf bezels
    5.  
      Installing the compute node rack rails
    6.  
      Installing the compute node into a rack
    7.  
      Connecting the hardware to one compute node
    8.  
      Connecting the hardware to two compute nodes
    9.  
      Connecting Access nodes to the network
    10.  
      Connecting the power cords to the hardware
    11.  
      Turning on the hardware and verifying operation
    12.  
      Configuring the IPMI port
    13.  
      Accessing and using the Veritas Remote Management interface
  4. Appendix A. Adding Expansion Storage Shelves to an operating appliance that does not have any Expansion shelves
    1.  
      Overview
    2.  
      Turning off the existing hardware
    3.  
      Installing the hardware
    4.  
      Connecting one Expansion shelf to the Primary shelf
    5.  
      Connecting two Expansion shelves to the Primary shelf
    6.  
      Connecting three Expansion shelves to the Primary shelf
  5. Appendix B. Adding Expansion Storage Shelves to an operating appliance that has at least one operating Expansion shelf
    1.  
      Overview
    2.  
      Turning off the existing hardware
    3.  
      Installing the hardware
    4.  
      Connecting one Expansion shelf to a system that has one existing Expansion shelf
    5.  
      Connecting two Expansion shelves to a system that has one existing Expansion shelf
    6.  
      Connecting one Expansion shelf to a system that has two existing Expansion shelves
  6. Appendix C. Configuring the disk space after adding one or more new Expansion Storage Shelves
    1.  
      Adding the disk space of an Expansion Storage Shelf from the Access Appliance shell menu

Dimensions and determining rack locations

Physical specifications for the compute node include the following.

  • Each node is two rack units (2RU) high.

  • Node measurements are listed below.

    • Height: 21.97cm (8.65")

    • Width: 48.26cm (19")

    • Length/depth: 79.38cm (31.25")

  • The compute node rails are extensible to 813mm (32in). This distance is the maximum depth that is allowed between rack posts.

Physical specifications for the 5U84 storage shelves include the following.

  • Each storage shelf is 5RU high.

  • Storage shelf measurements are listed below.

    • Height: 22.23cm (8.75")

    • Width: 48.26cm (19")

    • Length/depth: 93.35cm (36.75") from the rear of the front flanges to the extreme rear of the storage shelf chassis.

      Note:

      The 5U84 storage shelf is longer than a standard IEC-compliant rack. Be sure that your rack cabinet and Power Distribution Units accommodate the length of the storage shelves.

  • The storage shelf rails measure 71.3cm to 88.4cm (28" to 34.8") in length. Be sure that your rack accommodates this distance from the inside of the front post to the inside of the rear post. Plan for additional space to accommodate power strips, power cords, and other cables.

When you plan the installation be sure to allocate enough space for all of the hardware.

A typical installation has the storage shelves on the bottom and the compute node(s) at the top.

To help you identify RU spacing, many rack manufacturers use a system of lines and sequential numbers starting at the bottom of the rack. The front and the rear of the rack are marked the same to ensure that the rails are installed straight and level. One RU has three holes. The holes for one RU are typically marked with a line below the bottom hole and another line at the top hole.

Use the rack templates to determine the mounting locations for all devices.

To determine rack locations for the hardware

  1. Determine the total number of rack units (RUs) that you need as follows:
  2. Use the rack templates to determine RU locations.
  3. Fold the compute node templates at the horizontal yellow lines.
  4. Use the following graphics to determine where pins and screws for the storage shelves fit into the rack.

    • The front of each rail includes four pins that insert into the rear of the front rack post. One screw fits into the middle hole of the middle RU.

    • The rear of each rail includes four pins that insert into the inside of the rear rack post. Two screws insert into the front of the rear rack post. The screws install into the middle hole in the first and the fifth RU.

  5. Record the rack positions to help you locate them easily when mounting the hardware.