Veritas NetBackup™ Flex Scale Installation and Configuration Guide

Last Published:
Product(s): Appliances (3.2)
Platform: NetBackup Flex Scale OS
  1. Preparing for NetBackup Flex Scale deployment
    1.  
      Deployment overview
    2.  
      Deployment options
  2. Configuring NetBackup Flex Scale
    1. Assigning public IP address to a management network interface
      1.  
        Assigning a public IP address to network adapter eth1 or to a VLAN on eth1 of a node
      2.  
        Configuring a bond device and assigning an IP address to the bonded device or to a VLAN on the bonded device
    2.  
      NetBackup Flex Scale configuration methods
    3.  
      Configuring NetBackup Flex Scale using the setup wizard
    4.  
      YML configuration file
  3. Upgrading NetBackup Flex Scale to 3.2
    1.  
      About NetBackup Flex Scale upgrades and EEBs
    2.  
      NetBackup Flex Scale upgrade overview
    3.  
      About parallel upgrade and supported upgrade paths
    4.  
      Downloading the upgrade file
    5.  
      Uploading the upgrade file and performing an upgrade precheck
    6. Performing pre-upgrade tasks
      1.  
        Considerations for upgrade when disaster recovery is configured
    7.  
      Performing an upgrade using GUI
    8. Performing post-upgrade tasks
      1.  
        Downloading and installing the required EEBs
      2.  
        Verifying appliance firmware compatibility
      3.  
        Adding NetBackup license file
      4.  
        Saving the default password of the HPE iLO Administrator user
      5.  
        Collecting logs post upgrade
    9.  
      Collecting logs for an upgrade precheck failure
  4. Upgrading NetBackup Flex Scale to 3.2.100
    1.  
      About NetBackup Flex Scale upgrades and EEBs
    2.  
      NetBackup Flex Scale upgrade overview
    3.  
      Supported upgrade paths
    4.  
      Downloading the upgrade file
    5.  
      Uploading the upgrade file and performing an upgrade precheck
    6. Performing pre-upgrade tasks
      1.  
        Considerations for upgrade when disaster recovery is configured
    7.  
      Performing an upgrade using GUI
    8. Performing post-upgrade tasks
      1.  
        Downloading and installing the required EEBs
      2.  
        Rolling back NetBackup EEBs
      3.  
        Verifying appliance firmware compatibility
      4.  
        Adding NetBackup license file
      5.  
        Saving the default password of the HPE iLO Administrator user
      6.  
        Collecting logs post upgrade
    9.  
      Collecting logs for an upgrade precheck failure
  5. Upgrading the firmware in NetBackup Flex Scale cluster
    1.  
      About firmware upgrades
    2.  
      Determining if a firmware upgrade is required
    3.  
      Downloading the firmware package
    4.  
      About the firmware upgrade options
    5. Upgrading the firmware
      1. Updating the firmware in NetBackup Flex Scale clusters using HPE iLO
        1.  
          Upgrading the firmware using the rolling method
        2.  
          Upgrading the firmware using the parallel method
        3.  
          Updating the ACL file on the cluster nodes
  6. Managing EEBs
    1.  
      Downloading EEBs
    2.  
      Installing EEBs using GUI
    3.  
      Installing EEBs using REST APIs
  7. Removing NetBackup Flex Scale
    1. About disk erasure
      1.  
        Configuring data erasure
      2.  
        Viewing the data erasure status
      3.  
        Aborting data erasure
    2.  
      About NetBackup Flex Scale node factory reset
    3.  
      Performing a factory reset on a node
  8. Appendix A. Installing NetBackup Flex Scale 3.2 from a USB drive
    1.  
      Installing NetBackup Flex Scale on HPE ProLiant DL380 Gen10 servers using a USB drive
    2.  
      Installing NetBackup Flex Scale on HPE ProLiant DL380 Gen11 servers using a USB drive
  9. Appendix B. Installing NetBackup Flex Scale using a downloaded ISO file
    1.  
      About NetBackup Flex Scale software installation
    2.  
      Enabling remote IPMI connections
    3.  
      Setting up the RAID configuration on the nodes
    4.  
      Configuring the BIOS settings on the nodes
    5.  
      Downloading the product installer ISO
    6.  
      Mounting the ISO file on the nodes
    7.  
      Installing NetBackup Flex Scale using the ISO
  10. Appendix C. Upgrading a NetBackup Flex Scale node
    1.  
      Upgrading a node that is not in a cluster

About firmware upgrades

The appliance nodes include multiple hardware components, which have firmware installed on them. Hardware vendors release new firmware versions periodically to fix issues or to improve the security and performance of the components. These updates are made available as firmware packages. You must upgrade the firmware on the appliance nodes when new firmware packages are made available.

Each node includes an acl_info.json appliance compatibility list (ACL) file that maintains a list of latest supported firmware versions for each of the components. If the firmware version of an appliance node component does not match the version that is listed in the ACL file, alerts are generated and the node is marked unhealthy.

Note:

You can upgrade directly to the latest firmware version (n) if you are upgrading from the previous two firmware versions (n-2) or (n-1).

However, if you are upgrading from an older firmware version directly to the latest available firmware version, some of the appliance components might not upgrade successfully. In such situations, you need to follow a multi-step path and upgrade to intermediate firmware versions (n-2) or (n-1), and then upgrade to version n where n denotes the latest firmware version.

To upgrade the firmware, refer to the following steps:

See Determining if a firmware upgrade is required.

See Downloading the firmware package.

See About the firmware upgrade options.

See Upgrading the firmware.

See Updating the ACL file on the cluster nodes. (if required)