NetBackup™ Clustered Primary Server Administrator's Guide

Last Published:
Product(s): NetBackup & Alta Data Protection (10.4)
  1. Introduction to NetBackup primary server clustering
    1. About NetBackup clustering
      1.  
        About security certificates in NetBackup
      2.  
        NetBackup clustering in virtual environment
    2.  
      About NetBackup failover server data protection in a cluster
    3.  
      About NetBackup failover server support
    4.  
      NetBackup supported cluster solutions
    5.  
      About NetBackup limitations with clustering solutions
  2. NetBackup in a Windows Server Failover Clustering
    1.  
      About NetBackup on Windows Server Failover Clustering
    2.  
      Installation prerequisites for NetBackup on WSFC cluster
    3.  
      Installing a NetBackup failover server on WSFC cluster
    4.  
      Configuring a NetBackup server on WSFC cluster
    5.  
      Upgrading a NetBackup failover server on WSFC cluster
    6.  
      Restoring the cluster quorum
    7.  
      Restoring the cluster quorum to a node with directory services
    8.  
      Preparation for disaster recovery of WSFC
    9.  
      Disaster recovery of WSFC
    10.  
      Recovering the entire WSFC cluster
    11.  
      Recovering all shared disks
    12.  
      About recovering NetBackup data on a shared disk
  3. NetBackup in a Veritas Cluster Server on Linux
    1.  
      About NetBackup on a Veritas Cluster Server on Linux
    2.  
      Installation prerequisites for NetBackup on VCS on Linux
    3. About preinstallation checklist for a NetBackup failover server installation on VCS on Linux
      1.  
        NetBackup installation information for all VCS configurations
      2.  
        NetBackup installation information for specific VCS configurations
    4.  
      Installing a failover NetBackup server on VCS on Linux
    5.  
      Configuring a failover NetBackup server on VCS on Linux
    6.  
      About adding a node to existing cluster
    7.  
      Installing or upgrading NetBackup options on VCS on Linux
    8.  
      Upgrading a NetBackup failover server on VCS on Linux
  4. NetBackup in a Veritas Cluster Server on Windows
    1.  
      About NetBackup in a Veritas Cluster Server on Windows
    2.  
      About NetBackup agent for VCS on Windows
    3.  
      Installation prerequisites for NetBackup on VCS on Windows
    4.  
      Installing a NetBackup failover server on VCS on Windows
    5.  
      Configuring a NetBackup server on VCS on Windows
    6.  
      Upgrading a NetBackup failover server on VCS on Windows
    7.  
      Setting up a detailed monitoring script for the NetBackup server on VCS on Windows
    8.  
      Enabling detailed monitoring in VCS Cluster Manager for the NetBackup server
    9.  
      Disabling detailed monitoring in VCS Cluster Manager for the NetBackup server
  5. NetBackup on RedHat Pacemaker (PCS) on Linux
    1.  
      About NetBackup on a Red Hat Pacemaker (PCS) on Linux
    2.  
      Installation prerequisites for NetBackup on PCS Linux
    3.  
      Preinstallation checklist for a NetBackup failover server installation on PCS on Linux
    4.  
      NetBackup installation on Red Hat Pacemaker Passive Node on Linux
  6. Configuring NetBackup
    1.  
      NetBackup configuration overview
    2.  
      NetBackup configuration guidelines
    3.  
      Device configuration guidelines
    4.  
      Configuring devices
    5.  
      Configuring NetBackup catalog backups in a cluster
    6.  
      About configuring backup policies for a NetBackup clustered server
    7.  
      What to back up
    8.  
      Guidelines for backing up local disks in a cluster
    9.  
      Guidelines for backing up the shared disks
    10.  
      Verifying NetBackup configuration
    11.  
      Configuring robotic daemons for monitoring (UNIX/Linux clusters)
    12.  
      Configuring additional services (UNIX/Linux clusters)
    13.  
      Configuring add-ons for monitoring (UNIX/Linux clusters)
    14.  
      Configuring additional services (Windows)
    15.  
      Configuring add-ons for monitoring (Windows)
    16.  
      About adding license keys
  7. Operational notes
    1.  
      General notes on clustered primary server administration
    2.  
      About WSFC clusters
    3.  
      About NetBackup cluster application management
    4.  
      Logging information
    5.  
      About the support for multiple IP addresses in NetBackup
    6.  
      Log on to server using virtual name
    7.  
      Normal error messages when upgrading clustered servers
  8. Appendix A. NetBackup primary server in a cluster using multiple interfaces
    1.  
      About NetBackup primary server in a cluster using multiple interfaces
    2.  
      Requirements for use of a NetBackup primary server in a cluster with multiple interfaces
    3.  
      Configuring the NetBackup primary server in a cluster using multiple interfaces

Installation prerequisites for NetBackup on WSFC cluster

The following requirements must be met before you install and configure a NetBackup failover server in a WSFC environment:

  • Verify that WSFC and the current NetBackup version support your hardware. For a list of supported storage devices, visit the following Web site. Also consult the WSFC documentation.

    https://www.veritas.com/support/en_US/article.000033647

  • Verify that storage devices are properly installed and configured to work in a Windows environment. Refer to the information on configuring storage devices in the NetBackup Installation Guide.

  • Verify that Windows Server Failover Clustering is correctly installed and configured. NetBackup can be installed on as many nodes as WSFC supports. WSFC supports up to 4 or 8 nodes in a cluster, depending on the level of Windows that is installed.

  • Physically connect the robotic devices and tape devices to each node where you want to install NetBackup). Connect devices by SCSI or Fibre Channel. Use OS commands to verify that all the devices are connected properly.

    See the NetBackup Device Configuration Guide.

  • Verify that you have an IP address and host name (virtual name) to be assigned to the NetBackup cluster group. Use these only for the NetBackup cluster group.

    Also, verify that the disk resource is online on the node from which the NetBackup installation is about to be performed for the first time on the cluster.

    With this release IPv6 is supported with NetBackup.

  • Use Cluster Administrator to verify that the Possible Owners list for each disk resource that NetBackup uses includes each node to which NetBackup can failover.

  • Verify that you have the current NetBackup Primary Server version or the current NetBackup server version installation program and a valid license.

  • The Windows Server Failover Clustering Administrator must be installed on all NetBackup servers that you use to administer the NetBackup failover primary server remotely. Failover Cluster Manager must also be installed on any NetBackup administration clients.

  • You must have administrator rights or domain administrator credentials on the server cluster.

  • On Windows, the public network names must be the same on both nodes of the cluster for push installs.

  • You should install NetBackup on the same path on all the nodes.

More Information

About the support for multiple IP addresses in NetBackup