Veritas Access Appliance Command Reference Guide
- Overview
- Appendix A. Main > Appliance
- Appendix B. Main > Manage > Cluster
- Appendix C. Main > Manage > Software
- Appendix D. Main > Manage > Storage
- Appendix E. Main > Network
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > NetStat
- Network > NTPServer
- Network > Unconfigure
- Network > VLAN
- Network > TraceRoute
- Network > Ping
- Network > Hostname
- Network > Proxy
- Appendix F. Main > Monitor
- Appendix G. Main > Settings
- Appendix H. Main > Support
Name
Main > Support > IPMI — Use these commands to manage the IPMI configuration.
SYNOPSIS
IPMI Network Configure<IPAddress> <Netmask> <GatewayIPAddress>
IPMI Network Show
IPMI Reset
IPMI User Add <User_name>
IPMI User Delete <User_name>
IPMI User List
DESCRIPTION
The IPMI commands let you configure the IPMI network and manage users accessing the appliance using the IPMI connection. Use the IPMI commands to:
Configure IPMI sub-system
View the current IPMI settings
Reset the IPMI
Add users
Delete users
List users
OPTIONS
- IPMI Network Configure
This command is used to configure the IPMI sub-system using the IPMI port.
- IPMI Network Show
This command is used to view the current IPMI port information.
- IPMI Reset
This command is used to reset the IPMI. You must reset IPMI only if the IPMI interface stops responding or hangs.
- IPMI User Add
This command is used to add new users to access the IPMI sub-system.
- IPMI User Delete
This command is used to delete existing users that can access the IPMI sub-system.
- IPMI User List
This command is used to view the list of users who can access the IPMI sub-system.
The following procedure is executed after you run the IPMI Network Configure command.
Support> IPMI Network Configure 10.182.8.70 255.255.240.0 10.182.1.1 Network is configured successfully.
The following information is displayed when you run the IPMI Network Show command.
Support> IPMI Network Show IP Address Source : STATIC IP Address : 10.182.8.70 Subnet Mask : 255.255.240.0 Gateway IP Address : 10.182.1.1
The following information is displayed when you run the IPMI Reset command.
Resetting the IPMI disconnects all current IPMI users. Are you sure you want to reset the IPMI? [yes, no]: yes
In case other users are not affected, type and press to continue. The following message is displayed:
-[Info] The IPMI is being reset... -[Info] Wait for two minutes before attempting to reconnect to the IPMI console. If you cannot access the IPMI console, the appliance must be shut down and then restarted. First schedule a convenient time for the shutdown, alert all users and shut down the appliance. Then disconnect all appliance power cables for 15 seconds, reconnect them and turn on power to the appliance.
Type in case other users are affected. Alert all users and schedule a convenient time for reset. Run the IPMI Reset command again at the scheduled time.
The following procedure is executed after you run the IPMI User Add <User_name> command.
Support> IPMI User Add abc New password: Confirm password: Operation successful
The following procedure is executed after you run the IPMI User Delete <User_name> command.
Support> IPMI User Delete abc User abc has been deleted successfully.
The following information is displayed after you run the IPMI User List command.
Support > IPMI User List User name : Anonymous User User privilege : ADMIN User name : sysadmin User privilege : ADMIN User name : root User privilege : ADMIN