Search <book_title>...

Veritas Access 3350 Appliance Product Description

Last Published: 2025-03-27

Product(s): Appliances (8.4, 8.3, 8.2, 8.1, 8.0)

Platform: Veritas 3350

Veritas 5U84 Primary Storage Shelf RAID controllers

The Veritas 5U84 Primary Storage Shelf uses dual, hot swappable SAS-3 RAID controllers. These controllers create and manage the 5U84 Primary Storage Shelf disk drive RAID sets that contain backed up data. They also create and manage the RAID sets on 5U84 Expansion Storage Shelves when those are attached to the 5U84 Primary Storage Shelf.

The SAS-3 RAID controllers run RAID level 6 on the storage shelf. RAID 6 offers the highest level of data protection. It allows simultaneous write operations, while also allocating two sets of parity data across the drives that comprise the RAID 6 array.

The SAS-3 RAID controllers also provides an additional SAS-3 port. The SAS-3 port enables data to flow at SAS-3 data transfer rates between the 5U84 Primary Storage Shelf and the first optional 5U84 Expansion Storage Shelf.

Figure: Veritas 5U84 Primary Storage Shelf SAS-3 RAID controllers

The following figure and table provides component details for the Veritas 5U84 Primary Storage Shelf SAS-3 RAID controller modules.

Figure: Veritas 5U84 Primary Storage Shelf SAS-3 RAID Controller components and locations

Table: Veritas 5U84 Primary Storage Shelf SAS-3 RAID Controller components

Number	Component
1	Expansion SAS port
2	Ethernet port Note: Veritas does not use or support the Ethernet port.
3	USB port
4	Serial ports (Service only)
5	Indicator LEDs
6	SAS-3 RAID ports - connects to the 3350 Appliance compute nodes
7	Activity LEDs
8	Expansion SAS port Status

Figure: Veritas 5U84 Primary Storage Shelf SAS-3 RAID Controller indicator LED details

Table: Veritas 5U84 Primary Storage Shelf SAS-3 RAID Controller indicator LED details

LED	Description	Definition
1	Host 12Gb SAS-3 Link Status/Link Activity	Off - No link detected. Green- The port is connected and the link is up. Amber - Partial link exists (one or more lanes are down) Blinking green or amber- The link has I/O activity.
2	OK	Off - A controller issue has been detected, or the controller is turned off. Blinking green - The system is starting. Green - The controller is operating normally.
3	Fault	Off - The controller is operating normally. Amber - A controller fault has been detected or a service action is required. Blinking amber - Hardware-controller power on error, or a cache flush or restore error.
4	OK to Remove	Off - The controller is not prepared for removal. Blue - The controller is prepared for removal.
5	Identify	White - The controller is being identified.
6	Cache Status	Off - In a working controller, the cache is clean (contains no unwritten data). This is an occasional condition that occurs while the system is booting. Green - The cache is dirty (contains unwritten data) and the operation is normal. The unwritten information can be the log data or the debug data that remains in the cache. By itself, a Green cache status LED does not indicate that any user data is at risk or that any action is necessary. Blinking Green - A Compact Flash flush or a cache self-refresh is in progress, indicating cache activity.
7	Network Port Link Activity Status ^*	Off - The Ethernet link is not established, or the link is down. Green - The Ethernet link is up (applies to all negotiated link speeds).
8	Network Port Link Speed ^*	Off - The link is up at 10/100base-T negotiated speeds. Amber - The link is up and negotiated at 1000base-T speed.
9	SAS-3 Expansion Port Status	Off - The port is empty or the link is down. Green - The port is connected and the link is up.
^* When port is down, both LEDs are off