Please enter search query.
Search <book_title>...
NetBackup™ NAS Administrator's Guide
Last Published:
2024-03-27
Product(s):
NetBackup & Alta Data Protection (10.4)
- Section I. About NAS backups
- Section II. Using NAS-Data-Protection (D-NAS)
- D-NAS overview
- D-NAS Planning and Tuning
- Pre-requisites for D-NAS configuration
- Volume multi-host backup
- Configure D-NAS policy for NAS volumes
- Using accelerator
- Using Vendor Change Tracking
- Replication using D-NAS policy
- Restoring from D-NAS backups
- Troubleshooting
- Troubleshooting
- Setting the log level
- Logging directories for Linux platforms
- Logging folders for Windows platforms
- Logging folders for multi-stream restore
- Restore from a snapshot fails with status 133
- Backup from snapshot fails with error 50
- Backup from snapshot parent job fails with error 4213: Snapshot import failed
- Backup host pool creation fails with the error "Failed to fetch host list"
- Snapshot job fails and the snapshot command does not recognize the volume name
- Accelerator enabled incremental backup of NetApp NAS volume
- Snapshot method: Auto
- Backup from snapshot jobs for NAS-Data-Protection policy fail with error 4213
- A full VCT-enabled indexing job runs, when followed by a non-VCT indexing job with a backup host prior to version to 10.3
- Backup from snapshot jobs for NAS data protection policy fail with error 927
- Error code: 930: No supported media server is available in the All_Media_Server_Pool to use to backup the NAS shares.
- Multi-stream restore from NAS array volume fails with the status: 174 Media manager - system error occurred.
- NAS job fails with the error: Crawler process timed out after 600 seconds waiting for streams to attach with shared memory.
- Section III. Using NDMP
- Introduction to NetBackup for NDMP
- About NetBackup for NDMP
- About Network Data Management Protocol (NDMP)
- Types of NDMP backup
- About NDMP policies in NetBackup
- About NetBackup storage units
- About assigning tape drives to different hosts
- About the NDMP backup process
- About the NDMP restore process
- About Direct Access Recovery (DAR)
- Snapshot Client assistance
- About NDMP multiplexing
- About NDMP support for Replication Director
- Limitations of Replication Director with NDMP
- About NDMP support for NetApp clustered Data ONTAP (cDOT)
- Installation Notes for NetBackup for NDMP
- Configuring NDMP backup to NDMP-attached devices
- About configuring NDMP-attached devices
- Authorizing NetBackup access to a NAS (NDMP) host
- About access for three-way backups and remote NDMP
- About Media and Device Management configuration
- Using the Device Configuration Wizard to configure an NDMP filer
- About adding volumes
- About verifying NDMP password and robot connection
- Adding NDMP storage units
- About creating an NDMP policy
- About environment variables in the backup selections list
- About appropriate host selection for NetApp cDOT backup policies
- About backup types in a schedule for an NDMP policy
- About enabling or disabling DAR
- Configuring NetBackup for NDMP in a clustered environment
- Configuring NDMP backup to NetBackup media servers (remote NDMP)
- Configuring NDMP DirectCopy
- Accelerator for NDMP
- Remote NDMP and disk devices
- Using the Shared Storage Option (SSO) with NetBackup for NDMP
- NAS appliance information for NDMP
- About NAS appliances support
- Non-vendor-specific information
- Vendor-specific information
- Dell EMC Isilon
- Dell EMC VNX
- Dell EMC Unity
- EMC Celerra
- Hitachi HDI/VFP
- Hitachi NAS (HNAS)
- HP X9000 NAS
- Huawei OceanStor V3
- IBM System Storage Nxxxx
- NEC Storage NV series
- NetApp
- Using NetBackup with NetApp's Data ONTAP 8.2 cluster mode
- Using a node name as the NDMP client name in all versions of NetBackup
- Using a data Vserver LIF as the NDMP client name in non-CAB-aware versions of NetBackup
- Using a cluster_mgmt vserver LIF as the NDMP client name in non-CAB-aware versions of NetBackup
- Using a cluster_mgmt Vserver LIF as the NDMP client name in CAB-aware versions of NetBackup
- Using NetBackup with NetApp's Data ONTAP 8.2 cluster mode
- Nexenta
- Nexsan
- Oracle Axiom Series
- Oracle Solaris Server
- Stratus V Series
- Backup and restore procedures
- Troubleshooting
- Using NetBackup for NDMP scripts
- About the NetBackup for NDMP scripts
- ndmp_start_notify script (UNIX)
- ndmp_start_notify.cmd script (Microsoft Windows)
- ndmp_end_notify script (UNIX)
- ndmp_end_notify.cmd script (Microsoft Windows)
- ndmp_start_path_notify script (UNIX)
- ndmp_start_path_notify.cmd script (Microsoft Windows)
- ndmp_end_path_notify script (UNIX)
- ndmp_end_path_notify.cmd script (Microsoft Windows)
- ndmp_moving_path_notify script (UNIX)
- ndmp_moving_path_notify.cmd script (Microsoft Windows)
- Introduction to NetBackup for NDMP
About NetBackup storage units
NetBackup uses either one of the following storage units:
NDMP-type storage units (for local or three-way backup)
NetBackup requires NDMP-type storage units when you back up NDMP host data to the devices that are as follows:
Attached to an NDMP host
Available to the NDMP host on a SAN
An NDMP storage unit can contain standalone or robotic drives. Robotic controls can be in a TLD (tape library DLT) or ACS robot type.
Media Manager storage units (for backup to devices that are attached to a NetBackup media server)
You can use the drives that were configured in Media Manager-type storage units when you back up NDMP host data to devices that are as follows:
Attached to a NetBackup for NDMP server
Available to the server on a SAN
For NDMP backup, drives in Media Manager-type storage units do not have to be dedicated to NDMP data. They can store backups of regular (non-NDMP) NetBackup clients as well as of NDMP clients.