Please enter search query.
Search <book_title>...
Veritas NetBackup™ Plug-in for VMware vSphere Client (HTML5) Guide
Last Published:
2021-01-01
Product(s):
NetBackup (9.0.0.1, 9.0)
- Introduction and notes
- Installing the NetBackup plug-in for vSphere Client (HTML5)
- Requirements for the NetBackup plug-in for vSphere Client (HTML5)
- Using consistent vCenter naming with the NetBackup plug-in for vSphere Client (HTML5)
- vCenter privileges for managing NetBackup plug-in installation
- Notes on using the vSphere Client (HTML5) plug-in in a VMware Platform Services Controller (PSC) environment
- Installing the NetBackup plug-in for vSphere Client (HTML5)
- Upgrading the NetBackup plug-in for vSphere Client (HTML5)
- Uninstalling the NetBackup plug-in for vSphere Client (HTML5)
- Configuration overview for the NetBackup Recovery and Instant Recovery Wizards
- Configuring ports for the NetBackup Web Services
- Port usage for the NetBackup vSphere Client (HTML5) plug-in
- Creating an authentication token for the NetBackup plug-in for vSphere Client (HTML5)
- Authorizing the NetBackup vSphere Client (HTML5) plug-in to restore virtual machines
- Configuring the plug-in for an external certificate
- Reconfiguring the plug-in for a NetBackup CA-signed certificate
- Setting vCenter privileges for recovering virtual machines
- Adding or deleting an additional host name or IP address for an authentication token
- Revoking an authorization token
- Renewing an authorization token
- Listing all current authentication tokens
- Permissions on the NetBackup plug-in authentication token file may need to be changed
- Excluding virtual disks from the backup
- Monitoring backup status
- Restoring virtual machines
- Troubleshooting
- The message NoPermission appears during plug-in installation
- Reducing the load time for the NetBackup plug-in for vSphere Client (HTML5)
- A NetBackup master server is not available in the master server list of the Instant Recovery Wizard
- The NetBackup plug-in for vSphere Client (HTML5) does not find any backup images in the listed events
- The NetBackup Recovery wizard for vSphere Client (HTML5) does not find a particular backup image
- Mismatch in vCenter server name (uppercase vs. lowercase letters) causes the VMware connectivity test to fail
- Instant recovery operation is not complete due to NFS mount limit exceed
- Instant recovery-ready backup images are not available for selection
- The vCenter server and NetBackup master server names are not available for search
- Preferred Instant recovery destination options are not saved
- Virtual machine display name conflicts are not shown before the pre-recovery check
- Reasons for failure of pre-recovery checks
- Too much time taken to populate the list of NetBackup master servers
- The NetBackup plug-in is not shown in the vSphere Client (HTML5) interface even after registration
- The correct NetBackup master server does not show up for selection for a given vCenter server on the Instant recovery wizard
- Troubleshooting master server communication failures in the plug-in's Recovery Portal
- The NetBackup plug-in is not shown in the vSphere Client (HTML5) interface after vCenter upgrade from older versions to vCenter 7.0 or later
- Appendix A. Instant recovery events and best practices
- Appendix B. Installing the vSphere Client (HTML5) plug-in from a NetBackup media server and plug-in package host
Port usage for the NetBackup vSphere Client (HTML5) plug-in
The following table shows the standard ports to be used in a NetBackup plug-in environment.
Table: Ports used in NetBackup and the vSphere Client plug-in environment
Source | Port number | Destination |
|---|---|---|
Browser | 9443 | vSphere Client |
For VM recovery: vCenter server (or vSphere Client server if deployed independently) |
| Master server |
Master server | 443 | vCenter server |
Backup host | 443 | vCenter server |
Backup host | 902 (for | ESXi |