Veritas NetBackup™ Plug-in for VMware vSphere Client (HTML5) Guide
- Introduction and notes
- Installing the NetBackup plug-in for vSphere Client (HTML5)
- Requirements for the NetBackup plug-in for vSphere Client (HTML5)
- Using consistent vCenter naming with the NetBackup plug-in for vSphere Client (HTML5)
- vCenter privileges for managing NetBackup plug-in installation
- Notes on using the vSphere Client (HTML5) plug-in in a VMware Platform Services Controller (PSC) environment
- Installing the NetBackup plug-in for vSphere Client (HTML5)
- Upgrading the NetBackup plug-in for vSphere Client (HTML5)
- Uninstalling the NetBackup plug-in for vSphere Client (HTML5)
- Configuration overview for the NetBackup Recovery and Instant Recovery Wizards
- Configuring ports for the NetBackup Web Services
- Port usage for the NetBackup vSphere Client (HTML5) plug-in
- Creating an authentication token for the NetBackup plug-in for vSphere Client (HTML5)
- Authorizing the NetBackup vSphere Client (HTML5) plug-in to restore virtual machines
- Configuring the plug-in for an external certificate
- Reconfiguring the plug-in for a NetBackup CA-signed certificate
- Setting vCenter privileges for recovering virtual machines
- Adding or deleting an additional host name or IP address for an authentication token
- Revoking an authorization token
- Renewing an authorization token
- Listing all current authentication tokens
- Permissions on the NetBackup plug-in authentication token file may need to be changed
- Excluding virtual disks from the backup
- Monitoring backup status
- Restoring virtual machines
- Troubleshooting
- The message NoPermission appears during plug-in installation
- Reducing the load time for the NetBackup plug-in for vSphere Client (HTML5)
- A NetBackup master server is not available in the master server list of the Instant Recovery Wizard
- The NetBackup plug-in for vSphere Client (HTML5) does not find any backup images in the listed events
- The NetBackup Recovery wizard for vSphere Client (HTML5) does not find a particular backup image
- Mismatch in vCenter server name (uppercase vs. lowercase letters) causes the VMware connectivity test to fail
- Instant recovery operation is not complete due to NFS mount limit exceed
- Instant recovery-ready backup images are not available for selection
- The vCenter server and NetBackup master server names are not available for search
- Preferred Instant recovery destination options are not saved
- Virtual machine display name conflicts are not shown before the pre-recovery check
- Reasons for failure of pre-recovery checks
- Too much time taken to populate the list of NetBackup master servers
- The NetBackup plug-in is not shown in the vSphere Client (HTML5) interface even after registration
- The correct NetBackup master server does not show up for selection for a given vCenter server on the Instant recovery wizard
- Troubleshooting master server communication failures in the plug-in's Recovery Portal
- The NetBackup plug-in is not shown in the vSphere Client (HTML5) interface after vCenter upgrade from older versions to vCenter 7.0 or later
- Appendix A. Instant recovery events and best practices
- Appendix B. Installing the vSphere Client (HTML5) plug-in from a NetBackup media server and plug-in package host
Summary display
This display summarizes backup status, backup events, and backup age for the VMs in the vSphere object that you select. If you select an individual VM, the Summary display shows backup status and events for that VM.
The following shows an example of the Summary display for multiple VMs.
The Summary display presents the following backup information.
Table: Summary display in the NetBackup plug-in for vSphere Client (HTML5)
Panel | Description |
|---|---|
Virtual Machines | Shows the current backup status for a particular VM or for all the VMs that belong to the selected vSphere object. If the vSphere object is higher than the level of a VM, the backup status appears in a color-coded pie chart. Note: If the panel applies to more than one VM: click on the linked values (such as for or ) to see the details in the Virtual Machines display. |
Virtual Machines By Backup Age | Shows the backup age of the VMs in a bar chart. This panel is available only for a vSphere object that is higher than the level of a VM. |
Backup Events | Lists the total number of backup events and a breakdown of the events by Backup Successful, Backup Failed, and Snapshot Delete Failed. Note: Click on the linked values for , , , or to see the details in the Events display. Includes a color-coded bar chart that represents the type and number of backup events that occurred within a specified period. You can configure the chart as follows:
|