Veritas Access Troubleshooting Guide

Last Published:
Product(s): Appliances (7.3.2)
Platform: 3340
  1. Introduction
    1.  
      About troubleshooting
    2.  
      General tips for the troubleshooting process
    3.  
      General techniques for the troubleshooting process
  2. General troubleshooting procedures
    1.  
      About general troubleshooting procedures
    2.  
      Viewing the Veritas Access log files
    3.  
      About event logs
    4.  
      About shell-activity logs
    5.  
      Setting the CIFS log level
    6.  
      Setting the NetBackup client log levels and debugging options
    7.  
      Retrieving and sending debugging information
    8.  
      Insufficient delay between two successive OpenStack commands may result in failure
  3. Monitoring Veritas Access
    1.  
      About monitoring Veritas Access operations
    2.  
      Monitoring processor activity
    3.  
      Generating CPU and device utilization reports
    4.  
      Monitoring network traffic
    5.  
      Exporting and displaying the network traffic details
  4. Common recovery procedures
    1.  
      About common recovery procedures
    2.  
      Restarting servers
    3. Bringing services online
      1.  
        Using the services command
    4.  
      Recovering from a non-graceful shutdown
    5.  
      Testing the network connectivity
    6.  
      Troubleshooting with traceroute
    7.  
      Using the traceroute command
    8.  
      Collecting the metasave image of a file system
    9.  
      Replacing an Ethernet interface card
    10. Speeding up replication
      1.  
        About synchronizing a replication job
      2.  
        Synchronizing an episodic replication job
    11.  
      Uninstalling a patch release or software upgrade
  5. Troubleshooting the Veritas Access cloud as a tier feature
    1.  
      Troubleshooting tips for cloud tiering
    2.  
      Issues when reading or writing data from the cloud tier
    3.  
      Log locations for checking for cloud tiering errors
  6. Troubleshooting Veritas Access installation and configuration issues
    1.  
      How to find the management console IP
    2.  
      Viewing the installation logs
    3.  
      Installation fails and does not complete
    4.  
      Excluding PCI IDs from the cluster
    5.  
      Cannot recover from root file system corruption
    6.  
      The storage disk list command returns nothing
  7. Troubleshooting Veritas Access CIFS issues
    1.  
      User access is denied on a CTDB directory share
  8. Troubleshooting Veritas Access GUI startup issues
    1.  
      Resolving GUI startup issues

Replacing an Ethernet interface card

In some cases, you may need to replace an Ethernet interface card on a node. This section describes the steps to replace the card.

Note:

This procedure works for replacing an existing Ethernet interface card. It does not work for adding an Ethernet interface card to the cluster. If the Ethernet interface card you add needs a new device driver, install the new device driver before installing the Ethernet interface card on the node.

To replace an Ethernet interface card

  1. Use the Cluster> shutdown command to shut down the node.

    For example:

    Cluster> shutdown access_03
Stopping Cluster processes on access_03.......done
Sent shutdown command to access_03
  2. Use the Cluster> del command to delete the node from the cluster.

    For example:

    Cluster> del access_03
  3. Install the replacement Ethernet interface card on the node.
  4. Turn on the node.
  5. Make sure that the Ethernet interface card is active and online.
  6. Use the Cluster> add command to add the node back into the cluster.

    For example:

    Cluster> add 172.16.113.118

For details on the Cluster> add and Upgrade>commands that are described in this section, see the relevant man pages.