NetBackup IT Analytics Data Collector Installation Guide for Fabric Manager

Last Published:
Product(s): NetBackup IT Analytics (11.1)
  1. Fabric Manager Data Collection overview
    1.  
      Introduction
    2.  
      Fabric Manager: Collection of SAN switch data
    3.  
      Switch zone alias collection
  2. Pre-Installation setup for Brocade switch
    1.  
      Pre-Installation setup for Brocade switch
    2.  
      Prerequisites for adding Data Collectors (Brocade switch)
    3.  
      Upgrade troubleshooting: Brocade BNA SMI-S (CIM) server and Java 11
    4.  
      Supported switches
    5.  
      Brocade switches: Default ports and firewall considerations
    6.  
      Installation overview (Brocade switch)
    7.  
      Brocade switch Data Collector policy
  3. Pre-Installation setup for Cisco switch
    1.  
      Pre-Installation setup for Cisco switch
    2.  
      Prerequisites for adding Data Collectors (Cisco switch)
    3.  
      Upgrade troubleshooting: Cisco DCNM SMI-S (CIM) server and Java 11
    4.  
      Cisco switches: Default ports and firewall considerations
    5.  
      Installation overview (Cisco switch)
    6.  
      Cisco switch Data Collection policy
    7.  
      Before you start Cisco switch Data Collection
  4. Pre-Installation setup for Brocade Zone alias
    1.  
      Pre-Installation setup for Brocade zone alias
    2.  
      Prerequisites for adding Data Collectors (Brocade zone alias)
    3.  
      Brocade switches: Default ports and firewall considerations
    4.  
      Installation overview (Brocade zone alias)
    5.  
      Brocade zone alias Data Collector policy
  5. Pre-Installation setup Cisco Zone alias
    1.  
      Pre-Installation setup Cisco zone alias
    2.  
      Prerequisites for adding Data Collectors (Cisco zone alias)
    3.  
      Cisco switches: Default ports and firewall considerations
    4.  
      Installation overview (Cisco Zone Alias)
    5.  
      Cisco zone alias Data Collector policy
  6. Installing the Data Collector software
    1.  
      Introduction
    2.  
      Installing the WMI Proxy service (Windows host resources only)
    3.  
      Testing WMI connectivity
    4.  
      Considerations to install Data Collector on non-English systems
    5.  
      Install Data Collector Software on Windows
    6.  
      Install Data Collector software on Linux
    7.  
      Deploy Data Collector in native Kubernetes environment
    8.  
      Configure Data Collector manually for Veritas NetBackup
  7. Validating Data Collection
    1.  
      Validation methods
    2.  
      Data Collectors: Vendor-Specific validation methods
    3. Working with on-demand Data Collection
      1.  
        View real-time logging during an on-demand collection
    4.  
      Using the CLI check install utility
    5.  
      List Data Collector configurations
  8. Uninstalling the Data Collector
    1.  
      Uninstall the Data Collector on Linux
    2.  
      Uninstall the Data Collector on Windows
  9. Manually starting the Data Collector
    1.  
      Introduction
  10. Appendix A. Firewall configuration: Default ports
    1.  
      Firewall configuration: Default ports

Before you start Cisco switch Data Collection

The Data Collector uses SMI-S to communicate with the Cisco switches to gather data. To ensure that the SMI-S provider is running, be sure to enable the Common Information Model (CIM) Server on the switch using the following CLI commands:

  • cimserver status: To execute this command, you need to be in enable mode.

  • show cimserver

  • config t - This puts you into configuration mode.

  • comserver enable - Once you are in configuration mode, this command turns on the SMI-S provider.