Cluster Server 7.4.1 Implementation Guide for Microsoft Exchange 2010 - Windows

Last Published:
Product(s): InfoScale & Storage Foundation (7.4.1)
Platform: Windows
  1. Introducing the VCS agents for Exchange and NetApp
    1.  
      About VCS support for Exchange 2010 and NetApp
    2. About the VCS database agent for Exchange 2010
      1.  
        Agent functions
      2.  
        Agent state definitions
    3. About the VCS hardware replication agent for NetApp
      1.  
        About the NetApp Filer agent
      2.  
        About the NetApp SnapDrive agent
      3.  
        About the NetApp SnapMirror agent
    4. How the VCS agents make Exchange highly available
      1.  
        Local cluster configuration
      2.  
        Disaster recovery configuration
    5. Typical Exchange configurations in a VCS cluster
      1.  
        Active-Active failover configuration
      2.  
        Disaster recovery configuration for Exchange
  2. Installing the product and configuring a VCS cluster
    1.  
      About installing the VCS agents
    2. Configuring the cluster using the Cluster Configuration Wizard
      1.  
        Configuring notification
      2.  
        Configuring Wide-Area Connector process for global clusters
  3. Installing Microsoft Exchange Server 2010
    1.  
      About installing Exchange 2010 in a VCS environment
    2. Before you install Exchange 2010
      1.  
        Configuring Microsoft iSCSI initiator
    3. Managing storage using NetApp filer
      1.  
        Connecting virtual disks to the cluster node
      2.  
        Disconnecting virtual disks from the cluster nodes
    4. Managing storage using Windows Logical Disk Manager
      1.  
        Reserving disks (if you use Windows LDM)
      2.  
        Creating volumes (if you use Windows LDM)
      3.  
        Mounting volumes (if you use Windows LDM)
      4.  
        Unassigning a drive letter
      5.  
        Releasing disks (if you use Windows LDM)
    5. Installing Exchange Server 2010
      1.  
        Creating mailbox databases on shared storage
  4. Configuring the Exchange database service group
    1.  
      About configuring the Exchange service group
    2.  
      Prerequisites for configuring the Exchange database service group
    3. Creating the Exchange database service group
      1.  
        Running SnapManager for Exchange
      2.  
        About the modifications required for tagged VLAN or teamed network
    4. About verifying the service group configuration
      1.  
        Bringing the service group online
      2.  
        Taking the service group offline
      3.  
        Switching the service group
    5. About modifying the Exchange database service group configuration
      1.  
        Prerequisites for modifying an Exchange database service group
      2.  
        Modifying the Exchange database service group
    6.  
      Deleting the Exchange service group
  5. Making a standalone Exchange server highly available
    1.  
      High availability configuration for a standalone server
    2.  
      Moving mailbox databases to shared storage
  6. Deploying Disaster Recovery for Exchange Server
    1.  
      About disaster recovery configuration
    2.  
      Setting up disaster recovery configuration
    3.  
      Configure replication using NetApp SnapMirror
    4.  
      Configure NetAppSnapMirror resources at the primary site
    5.  
      Configure NetAppSnapMirror resources at the secondary site
  7. Removing the software components
    1.  
      About removing the software components
    2. Remove Microsoft Exchange
      1.  
        Removing a node without removing Microsoft Exchange
      2.  
        Removing a node and removing Microsoft Exchange
  8. Troubleshooting
    1.  
      About troubleshooting VCS agents for Exchange
    2.  
      VCS logging
    3.  
      VCS Cluster Configuration Wizard (VCW) logs
    4.  
      VCWsilent logs
    5.  
      NetApp agents error messages
  9. Appendix A. Resource type definitions
    1.  
      About resource type definitions
    2. Exchange database agent
      1.  
        Exchange 2010 database agent resource type definition
      2.  
        Exchange 2010 database agent attribute definitions
      3.  
        Dependency graph for an Exchange cluster
  10. Appendix B. Sample Configurations
    1.  
      About the sample configurations
    2.  
      Sample service group configuration

Configuring Wide-Area Connector process for global clusters

Configure the Wide-Area Connector process only if you are configuring a disaster recovery environment. The GCO option configures the wide-area connector (WAC) process for global clusters. The WAC process is required for inter-cluster communication. Configure the GCO Option using this wizard only if you are configuring a Disaster Recovery (DR) environment and are not using the Disaster Recovery wizard.

You can configure the GCO Option using the DR wizard. The Disaster Recovery chapters in the application solutions guides discuss how to use the Disaster Recovery wizard to configure the GCO option.

To configure the wide-area connector process for global clusters

  1. On the GCO Network Selection panel, specify the network information and then click Next.
    GCO configuration

    If the cluster has a ClusterService group configured, you can use the IP address configured in the service group or configure a new IP address.

    Do the following:

    • To specify an existing IP address, select Use existing IP resource and then select the IP address from the drop-down list.

    • To use a new IP address, do the following:

      • In case of IPv4, select IPV4 and then enter the IP address and associated subnet mask. Make sure that the specified IP address has a DNS entry.

      • In case of IPv6, select IPV6 and select the IPv6 network from the drop-down list.

        The wizard uses the network prefix and automatically generates a unique IPv6 address that is valid on the network.

        The IPv6 option is disabled if the network does not support IPv6.

    • Select a network adapter for each node in the cluster.

      The wizard lists the public network adapters along with the adapters that were assigned a low priority.

  2. Review the summary information and choose whether you want to bring the WAC resources online when VCS starts and then click Configure.
  3. Click Finish to exit the wizard.