Dynamic Multi-Pathing 8.0.1 Administrator's Guide - Windows

Last Published:
Product(s): InfoScale & Storage Foundation (8.0.1)
Platform: Windows
  1. Understanding DMPW
    1.  
      DMP overview
    2.  
      Major features of Dynamic Multi-Pathing
    3. How DMP works
      1. How DMP monitors I/O on paths
        1.  
          Path failover mechanism
      2.  
        Load balancing
      3.  
        DMP in a clustered environment
    4.  
      Multiple paths to disk arrays
    5.  
      Device discovery
  2. Setting up DMPW
    1.  
      Active/Active and Active/Passive settings
    2. Active/Active and Active/Passive settings in a cluster environment
      1.  
        DMP DSMs
      2.  
        SCSI-3 PGR technology
      3.  
        Enabling SCSI-3 PGR
    3. Add and remove paths
      1.  
        Adding a path
      2.  
        Removing a path
    4. Specify load balancing settings and the primary path
      1.  
        Specifying load balancing settings for an array
      2.  
        Specifying load balancing settings for a disk
      3.  
        Specifying the primary path for an array or disk
    5. Configuring DSMs without storage connection
      1.  
        Specify DSM settings without storage connection
  3. Administering DMPW
    1.  
      About administering DMP
    2. DMP DSMs menus
      1.  
        Displaying the menu for arrays
      2.  
        Commands for arrays
      3.  
        Displaying the menu for disks
      4.  
        Commands for paths of a disk
      5.  
        Statistics monitoring
      6.  
        Clear performance statistics
      7.  
        Device settings
      8.  
        Set primary path
      9.  
        Properties
    3. View array, disk, and path status
      1.  
        Array status
      2.  
        Device status
      3.  
        Path status
    4. vxdmpadm
      1.  
        vxdmpadm dsminfo
      2.  
        vxdmpadm arrayinfo
      3.  
        vxdmpadm deviceinfo
      4.  
        vxdmpadm pathinfo
      5.  
        vxdmpadm arrayperf
      6.  
        vxdmpadm deviceperf
      7.  
        vxdmpadm pathperf
      8.  
        vxdmpadm allperf
      9.  
        vxdmpadm iostat
      10.  
        vxdmpadm cleardeviceperf
      11.  
        vxdmpadm cleararrayperf
      12.  
        vxdmpadm clearallperf
      13.  
        vxdmpadm setdsmscsi3
      14.  
        vxdmpadm setarrayscsi3
      15.  
        vxdmpadm setattr dsm
      16.  
        vxdmpadm setattr array
      17.  
        vxdmpadm setattr device
      18.  
        vxdmpadm setattr path
      19.  
        vxdmpadm set isislog
      20.  
        vxdmpadm rescan
      21.  
        vxdmpadm disk list
      22.  
        vxdmpadm getdsmattrib
      23.  
        vxdmpadm getmpioparam
      24.  
        vxdmpadm setmpioparam
  4. Performance tuning
    1.  
      Specifying control timer settings for an array
  5. Troubleshooting
    1. Resolving DMP issues
      1.  
        When a DMP license is no longer valid
      2.  
        When an unknown disk group appears in a DMP environment
    2. Using status information
      1.  
        Path status
      2.  
        Path states
  6. Glossary
    1.  
      Dynamic Multi-Pathing glossary

Configuring DSMs without storage connection

On Windows Server operating systems, DMP DSM enables configuration of some DSM settings without a storage connection. When a storage array is later connected to a host under an MPIO management, the connected storage array inherits the policy that has been previously set in a DSM.

Support for DSM settings without storage connection applies to operations that are general for storage devices without specific knowledge of a DMP path of a storage device.

The following are settings you can configure for a DSM without storage connection:

  • Load balances: Active/Active, Active/Passive without choosing a primary path, Least Block, Balanced Path and Least Queue. The specific settings for Round Robin with Subset or Weighted Path load balances cannot be configured without a storage connection because the settings require the specific knowledge of a Volume Replicator path of a disk which does not exist yet.

  • SCSI-3: Enabling or disabling the setting for SCSI-3 support.

The VEA DSM Configuration command enables viewing a list of installed DSMs on a system and applying load balance settings and SCSI-3 support settings to the selected DSMs. These capabilities are also available through the vxdmpadm utility in the command line interface (CLI). In addition, you can use the CLI vxdmpadm getdsmattrib command to view existing settings for the installed DSMs.