Storage Foundation Cluster File System High Availability 8.0 Administrator's Guide - Linux

Displaying paths controlled by a DMP node, controller, enclosure, or array port

The vxdmpadm getsubpaths command lists all of the paths known to Dynamic Multi-Pathing (DMP). The vxdmpadm getsubpaths command also provides options to list the subpaths through a particular DMP node, controller, enclosure, or array port. To list the paths through an array port, specify either a combination of enclosure name and array port id, or array port worldwide name (WWN).

To list all subpaths known to DMP:

# vxdmpadm getsubpaths

NAME   STATE[A]   PATH-TYPE[M]         DMPNODENAME       ENCLR-NAME   CTLR   ATTRS
=============================================================================
sdaf   ENABLED(A) PRIMARY              ams_wms0_130      ams_wms0      c2       -
sdc    ENABLED    SECONDARY            ams_wms0_130      ams_wms0      c3       -
sdb    ENABLED(A)   -                  vm04_disk_24      disk          c0       -
sda    ENABLED(A)   -                  vm04_disk_25      disk          c0       -
sdaa   ENABLED    Active/Non-Optimized emc_clariion0_438 emc_clariion0 c1       -
sdak   ENABLED(A) Active/Optimized(P)  emc_clariion0_438 emc_clariion0 c6       -

The vxdmpadm getsubpaths command combined with the dmpnodename attribute displays all the paths to a LUN that are controlled by the specified DMP node name from the /dev/vx/dmp directory:

# vxdmpadm getsubpaths dmpnodename=sdby

NAME   STATE[A]   PATH-TYPE[M] CTLR-NAME  ENCLR-TYPE  ENCLR-NAME  ATTRS   PRIORITY
==================================================================================
sdbp   ENABLED      -          c1          EMC        emc0          -       -
sdbs   ENABLED      -          c1          EMC        emc0          -       -
sdbv   ENABLED      -          c6          EMC        emc0          -       -
sdby   ENABLED(A)   -          c6          EMC        emc0          -       -

For A/A arrays, all enabled paths that are available for I/O are shown as ENABLED(A).

For A/P arrays in which the I/O policy is set to singleactive, only one path is shown as ENABLED(A). The other paths are enabled but not available for I/O. If the I/O policy is not set to singleactive, DMP can use a group of paths (all primary or all secondary) for I/O, which are shown as ENABLED(A).

Paths that are in the DISABLED state are not available for I/O operations.

A path that was manually disabled by the system administrator displays as DISABLED(M). A path that failed displays as DISABLED.

You can use getsubpaths to obtain information about all the paths that are connected to a particular HBA controller:

# vxdmpadm getsubpaths ctlr=c1

NAME STATE[A]   PATH-TYPE[M]         DMPNODENAME        ENCLR-TYPE   ENCLR-NAME     ATTRS  PRIORITY
===================================================================================================
sdh  ENABLED    Active/Non-Optimized emc_clariion0_429  EMC_CLARiiON  emc_clariion0     -       -
sdr  ENABLED(A) Active/Optimized(P)  emc_clariion0_429  EMC_CLARiiON  emc_clariion0     -       -
sdm  ENABLED(A) Active/Optimized(P)  emc_clariion0_430  EMC_CLARiiON  emc_clariion0     -       -
sdw  ENABLED    Active/Non-Optimized emc_clariion0_430  EMC_CLARiiON  emc_clariion0     -       -

You can also use getsubpaths to obtain information about all the paths that are connected to a port on an array. The array port can be specified by the name of the enclosure and the array port ID, or by the WWN identifier of the array port:

# vxdmpadm getsubpaths enclosure=enclosure portid=portid
# vxdmpadm getsubpaths pwwn=pwwn

For example, to list subpaths through an array port through the enclosure and the array port ID:

# vxdmpadm getsubpaths enclosure=emc_clariion0 portid=A7

NAME STATE[A]   PATH-TYPE[M]         DMPNODENAME       ENCLR-NAME   CTLR ATTRS PRIORITY
=======================================================================================
sdal ENABLED(A) Active/Optimized     emc_clariion0_429 emc_clariion0 c6   -      -
sdr  ENABLED(A) Active/Optimized     emc_clariion0_429 emc_clariion0 c1   -      -
sdaq ENABLED    Active/Non-Optimized emc_clariion0_430 emc_clariion0 c6   -      -
sdw  ENABLED    Active/Non-Optimized emc_clariion0_430 emc_clariion0 c1   -      -

For example, to list subpaths through an array port through the WWN:

# vxdmpadm getsubpaths pwwn=50:06:01:67:3e:a0:75:95

NAME STATE[A]   PATH-TYPE[M]         CTLR-NAME ENCLR-TYPE   ENCLR-NAME     ATTRS PRIORITY
=========================================================================================
sdal ENABLED(A) Active/Optimized     c6        EMC_CLARiiON  emc_clariion0  -       -
sdr  ENABLED(A) Active/Optimized(P)  c1        EMC_CLARiiON  emc_clariion0  -       -
sdaq ENABLED    Active/Non-Optimized c6        EMC_CLARiiON  emc_clariion0  -       -
sdw  ENABLED    Active/Non-Optimized c1        EMC_CLARiiON  emc_clariion0  -       -

# vxdmpadm getsubpaths pwwn=20:00:00:E0:8B:06:5F:19

You can use getsubpaths to obtain information about all the subpaths of an enclosure.

# vxdmpadm getsubpaths enclosure=enclosure_name [ctlr=ctlrname]

To list all subpaths of an enclosure:

# vxdmpadm getsubpaths enclosure=emc_clariion0	
NAME         STATE[A]   PATH-TYPE[M] DMPNODENAME  ENCLR-NAME   CTLR    ATTRS
================================================================================
sdav         ENABLED(A) PRIMARY      emc_clariion0_1017 emc_clariion0 c3    -
sdbf         ENABLED    SECONDARY    emc_clariion0_1017 emc_clariion0 c3    -
sdau         ENABLED(A) PRIMARY      emc_clariion0_1018 emc_clariion0 c3    -
sdbe         ENABLED    SECONDARY    emc_clariion0_1018 emc_clariion0 c3    -

To list all subpaths of a controller on an enclosure:

# vxdmpadm getsubpaths enclosure=emc_clariion0

By default, the output of the vxdmpadm getsubpaths command is sorted by enclosure name, DMP node name, and within that, path name.

To sort the output based on the pathname, the DMP node name, the enclosure name, or the host controller name, use the -s option.

To sort subpaths information, use the following command:

# vxdmpadm -s {path | dmpnode | enclosure | ctlr} getsubpaths \
[all | ctlr=ctlr_name | dmpnodename=dmp_device_name | \
enclosure=enclr_name [ctlr=ctlr_name | portid=array_port_ID] | \
pwwn=port_WWN | tpdnodename=tpd_node_name] 

See Setting customized names for DMP nodes.