Please enter search query.
Search <book_title>...
Veritas NetBackup™ Device Configuration Guide
Last Published:
2018-02-16
Product(s):
NetBackup (8.1.1, 8.1)
- Introducing device configuration
- Section I. Operating systems
- AIX
- Before you begin configuring NetBackup on AIX
- RS/6000 AIX adapter number conventions
- About AIX persistent naming support
- About configuring robotic control device files in AIX
- About device files for SAN Clients on AIX
- About configuring tape drive device files in AIX
- About choosing a tape driver on AIX
- About non-QIC tape drives on AIX
- About extended-file marks for drives
- About fast-tape positioning (locate-block) on AIX
- About no rewind device files on AIX
- Creating AIX no rewind device files for tape drives
- Using multiple tape densities on AIX
- About SPC-2 SCSI reserve on AIX
- Disabling SPC-2 SCSI reserve in AIX
- About Sony AIT drives on AIX
- AIX command summary
- HP-UX
- Before you begin configuring NetBackup on HP-UX
- About robotic control on HP-UX
- About HP-UX device addressing schemes
- HP-UX tape drive device file requirements for NetBackup
- About device drivers and files for HP-UX persistent DSFs
- About configuring persistent DSFs
- About HP-UX legacy device drivers and files
- Creating device files for SAN Clients on HP-UX
- About configuring legacy device files
- About SPC-2 SCSI reserve on HP-UX
- Disabling SPC-2 SCSI reserve in HP-UX
- About disabling the HP-UX EMS Tape Device Monitor for a SAN
- HP-UX command summary
- Linux
- Before you begin on Linux
- About the required Linux SCSI drivers
- Verifying the Linux drivers
- About configuring robot and drive control for Linux
- Verifying the device configuration on Linux
- About SAN clients on Linux
- About SCSI persistent bindings for Linux
- About Emulex HBAs
- Utilities to test SCSI devices
- Linux command summary
- Solaris
- Before you begin on Solaris
- About the NetBackup sg driver
- Determining if the NetBackup sg driver is installed
- Special configuration for the Oracle StorEdge Network Foundation HBA driver
- About binding Fibre Channel HBA drivers
- Configuring Solaris 10 x86 for multiple drive paths
- Installing/reinstalling the sg and the st drivers
- Configuring 6 GB and larger SAS HBAs in Solaris
- Preventing Solaris driver unloading
- About Solaris robotic controls
- About Solaris tape drive device files
- Configuring Solaris SAN clients to recognize FT media servers
- Uninstalling the sg driver on Solaris
- Solaris command summary
- Windows
- AIX
- Section II. Robotic storage devices
- Robot overview
- Oracle StorageTek ACSLS robots
- About Oracle StorageTek ACSLS robots
- Sample ACSLS configurations
- Media requests for an ACS robot
- About configuring ACS drives
- Configuring shared ACS drives
- Adding tapes to ACS robots
- About removing tapes from ACS robots
- Robot inventory operations on ACS robots
- NetBackup robotic control, communication, and logging
- ACS robotic test utility
- Changing your ACS robotic configuration
- ACS configurations supported
- Oracle StorageTek ACSLS firewall configuration
- Device configuration examples
Configuring Solaris 10 x86 for multiple drive paths
To use multiple paths to the same tape drive, NetBackup requires that Solaris Multiplexed I/O (MPxIO) be disabled. MPxIO is enabled by default on Solaris 10 x86 systems.
Use the following procedure to disable MPxIO.
To disable MPxIO
- Use a text editor to open the following file:
/kernel/drv/fp.conf - Change the mpxio-disable value from no to yes. After the change, the line in the file should appear as follows:
mpxio-disable="yes"
- Save the changes and exit from the text editor.