Veritas NetBackup™ Virtual Appliance Documentation

To perform the initial configuration on a NetBackup Virtual Appliance with the combined master and media server role

1. After you have deployed a new virtual appliance, log on to the NetBackup Virtual Appliance Shell Menu.

   The logon is admin, and the default password is P@ssw0rd.

2. Use the following command to start the initial configuration:

   Main > Appliance > Configure

   A message about the Virtual Appliance Configuration Wizard appears.

3. The wizard takes you to the network configuration.

   Specify the following:

   • Hostname

     Enter a short host name or a fully qualified domain name (FQDN) for this appliance. As a best practice, Veritas recommends that you use FQDN.

     Caution:

     After the initial deployment has completed successfully, the only way to change the host name is to redeploy the appliance.

     Note:

     If you plan to configure Active Directory (AD) authentication on this appliance, the host name must be 15 characters or less. Otherwise, AD configuration can fail.

   • DNS domain name

     Enter a DNS domain name for this appliance.

   • IPv4 address

     Enter the IPv4 address to be used for this appliance.

   • Netmask

     Enter the netmask that corresponds to the IP address.

   • Gateway IP address

     Enter the IPv4 address of the gateway (network point) that acts as an entrance to another network.

   • DNS server 1 IP address

     Enter the IPv4 address of the primary DNS server for this appliance.

   • DNS server 2 IP address(Optional)

     Enter the IPv4 address of the secondary DNS server for this appliance.

   When you are prompted with the following message, choose whether you want to add the host name and IP address to the HOSTS file.

   The host name must be resolvable with a DNS or a HOSTS file for the initial configuration to be successful. Do you want to write the host name resolution information to the HOSTS file? [yes, no](no)

   Note:

   The host name must be resolvable with a DNS server or a HOSTS file for the initial configuration to be successful. If DNS is not available, you can add the host name and IP address to the HOSTS file.

4. After the network configuration is completed, the wizard prompts you to enter a Smart Meter customer registration key.

   Veritas Smart Meter helps you manage your NetBackup deployment more efficiently, spot trends, and plan for the future. To obtain a key, follow the onscreen prompts as described below:

   • Log in to the Veritas Smart Meter site with your VEMS credentials and go to the Registration Keys page to download the key.

   • The following shares have been opened on this appliance:

     CIFS share \<hostname or ip>\incoming_patches\customer_registration/

     NFS share <hostname or ip>:/inst/patch/incoming/customer_registration/

     Mount one of these share paths.

   • Upload the veritas_customer_registration_key.json file to the mounted share path.

5. Use the following command to verify that the automatic configuration completed successfully:

   Main > Appliance > Status

   The command output should contain a message similar to the following:

   Appliance Version is 3.3.0.1.
   
   Appliance is configured as master appliance.
   

   If the output does not show that the appliance is configured as a master appliance, you need to redeploy the appliance or perform other troubleshooting steps to fix the issue before you proceed to the next step. See Troubleshooting NetBackup Virtual Appliance initial deployment issues.

6. Use the following commands to change the admin, the maintenance, and the nbasecadmin account passwords from the known default password (P@ssw0rd):

   • Main > Settings > Password admin

   • Main > Settings > Password maintenance

   • Main > Settings > Password nbasecadmin

     Note:

     You cannot access the NetBackup web UI until you have changed the nbasecadmin user password.

   See Changing NetBackup Virtual Appliance user passwords.

7. Use the following command to set the time zone:

   Main > Network > TimeZone Set

   Select the appropriate time zone from the displayed list.

8. Use the following command to add a Network Time Protocol (NTP) server:

   Main > Network > NTPServer Add <Server>

   Where <Server> is the name of the NTPServer.

9. Add a permanent license key before the evaluation key expires with the following command:

   Main > Manage > License > Add

   You can locate your permanent license key from the Veritas Entitlement Management System (VEMS). To access VEMS, click Licensing on the Veritas Support website.

   Warning:

   If the correct license key is not installed, the appliance services stop functioning after the evaluation key expires. Make sure that the NetBackup license you add includes support for NetBackup Virtual Appliance.

   See Managing license keys on the NetBackup Virtual Appliance.

10. (Optional)

    If you want to configure an IPv6 address for the appliance, run the following command:

    Main > Network > IPv6 <IPAddress> <Prefix> InterfaceName

    Where <IPAddress> is the IPv6 address and <Prefix> is the prefix length.

    See About IPv4-IPv6-based network support.

11. (Optional)

    If you want to an IPv6 DNS server on the appliance, run the following command:

    Main > Network > DNS Add NameServer <IPAddress>

    Where <IPAddress> is the IPv6 address of the additional DNS server. Only global-scope and unique-local IPv6 addresses are allowed.

    See Configuring DNS and host name mapping for the NetBackup Virtual Appliance.

12. (Optional)

    If you want to use an external Certificate Authority (CA) for communication between the appliance and your other NetBackup hosts, run the following command:

    Main > Settings > NetBackup CertificateUsage Enable ECA

13. (Optional)

    If you plan to use this master server with a media server in a NAT network, perform the following tasks:

    • Enable the NetBackup DNAT feature on this master server as follows:

      Main > Settings > NetBackup DNAT Enable

    • Add the name of the media server to the NetBackup Servers list on this master server as follows:

      Main > Settings > NetBackup NATServers Add

14. Log on to the appliance from the NetBackup Administration Console and create a NetBackup catalog backup policy.

    By default, the master server appliance does not contain a NetBack catalog backup policy. To protect the NetBackup catalog, configure a catalog backup before using NetBackup for regular client backups.

    You can create a backup policy that uses a Storage Lifecycle Policy (SLP) to protect the NetBackup catalog. Use the SLP to back up the data to AdvancedDisk and then duplicate it to MSDP. You are then able to use Auto Image Replication to save your catalog backup off site. Veritas recommends that you use this replication-based strategy for disaster recovery (DR).

    Note:

    You must set a encryption passphrase for the disaster recovery package for the catalog to be successful. Catalog backups continue to fail until the passphrase is set.

    For more information about the security requirements for disaster recovery , see the NetBackup Security and Encryption Guide.